Civil Engineering

Permanent URI for this communityhttps://scholarworks.montana.edu/handle/1/30

The Department of Civil Engineering has strong affiliation with the Western Transportation Institute (WTI) and the Center for Biofilm Engineering (CBE), a graduated NSF research center. The department is also affiliated with a Montana Department of Transportation Design Unit located on the MSU campus.

Browse

Search Results

Now showing 1 - 10 of 27

Effect of Fines Content on Calcium Carbonate Precipitation and Thermal Properties of Biocemented Sand
(American Society of Civil Engineers, 2024-04) Gunyol, Pinar; Khosravi, Mohammad; Phillips, A. J.; Plymesser, Kathryn; Parker, Albert E.
In this study, the impacts to soil thermal properties during and after biocementation via microbially induced calcite precipitation (MICP) method on silty silica sand specimens with varying fines content (0%, 5%, and 15%) were investigated. Firstly, calcium conversion was measured after each pulse; then, the MICP-treated specimens were tested for cementation uniformity. The evolution of thermal conductivity of silty soils with the MICP treatment was assessed using a thermocouple probe. The results show that thermal conductivity of silty saturated sands increased by 17% for specimens treated to 9.7% CaCO3. The improvement in thermal conductivity was attributed to the formation of calcium carbonate bridges binding the soil grains together. The results suggested that the thermal conductivity of silty soil depends on water content, the number of treatment pulses, and the treatment uniformity through the soil specimen. Presence of fines content in the soil was found to play an important role in the distribution and uniformity of biocementation through the soil specimen. However, no statistically significant difference in the thermal conductivity values of MICP-treated specimens with different fines content was observed (𝑝>0.05). The average calcium carbonate content ranged between 10.7% and 7.2% for the soils with 0% and 15% fines content, respectively. The findings of this research could be used to improve the efficiency of geothermal boreholes and other energy geostructures using MICP by improving thermal conductivity of dry and partially saturated soil.
Exploring canyons beneath Devon Ice Cap for sub-glacial drainage using radar and thermodynamic modeling
(Cambridge University Press, 2024-09) Pierce, Chris; Skidmore, Mark; Beem, Lucas; Blankenship, Don; Adams, Ed; Gerekos, Christopher
Sub-glacial canyon features up to 580 m deep between flat terraces were identified beneath Devon Ice Cap during a 2023 radar echo sounding (RES) survey. The largest canyon connects a hypothesized brine network near the Devon Ice Cap summit with the marine-terminating Sverdrup outlet glacier. This canyon represents a probable drainage route for the hypothesized water system. Radar bed reflectivity is consistently 30 dB lower along the canyon floor than on the terraces, contradicting the signature expected for sub-glacial water. We compare these data with backscattering simulations to demonstrate that the reflectivity pattern may be topographically induced. Our simulated results indicated a 10 m wide canal-like water feature is unlikely along the canyon floor, but smaller features may be difficult to detect via RES. We calculated basal temperature profiles using a 2D finite difference method and found the floor may be up to 18°C warmer than the terraces. However, temperatures remain below the pressure melting point, and there is limited evidence that the canyon floor supports a connected drainage system between the DIC summit and Sverdrup Glacier. The terrain beneath Devon Ice Cap demonstrates limitations for RES. Future studies should evaluate additional correction methods near complex terrain, such as RES simulation as we demonstrate here.
Biodegradability of unheated and laboratory heated dissolved organic matter
(Royal Society of Chemistry, 2024-01) Islam Promi, Saraf; Gardner, Courtney M.; Hohner, Amanda K.
Following wildfires, partially combusted biomass remains on the forest floor and erosion from the landscape can release dissolved pyrogenic organic matter (dPyOM) to surface waters. Therefore, post-fire alterations to dissolved organic matter (DOM) in aquatic systems may play a vital role in DOM stability and biogeochemical cycles. Dissolved PyOM biodegradation remains poorly understood and is expected to vary with combustion temperature and fuel source. In this study laboratory heating and leaching of forest floor materials (soil and litter) were used to compare the biodegradability of unheated, low (250 °C), and moderate (450 °C) temperature leachates. Inoculation experiments were performed with river microbes. Dissolved organic carbon (DOC) and nitrogen (DON), inorganic nitrogen, and DOM optical properties were monitored for 38 days. Inoculation experiments showed significantly greater DOC biodegradation of low and moderate temperature samples (64% and 71%, respectively) compared to unheated samples (32%). The greater DOC biodegradation may be explained by lower molecular weight DOM composition of heated leachates which was supported by higher initial E2/E3 ratios (absorbance at 250 nm/365 nm). Further, the observed decrease in the E2/E3 ratio after incubation suggests biodegradation of smaller compounds. This trend was greater for heated samples than unheated DOM. Specific ultraviolet absorbance increased after incubation, suggesting biodegradation of aliphatic compounds. Inoculated moderate temperature samples showed the greatest DON degradation (74%), followed by low temperature (58%) and unheated (51%) samples. Overall, results suggest that low and moderate temperature dPyOM was more biodegradable than unheated DOM, which may have implications for aquatic biogeochemical cycling, ecosystem function, and water quality in fire-impacted watersheds.
Characterizing sub-glacial hydrology using radar simulations
(Copernicus GmbH, 2024-04) Pierce, Chris; Gerekos, Christopher; Skidmore, Mark; Beem, Lucas; Blankenship, Don; Sang Lee, Won; Adams, Ed; Lee, Choon-Ki; Stutz, Jamey
The structure and distribution of sub-glacial water directly influences Antarctic ice mass loss by reducing or enhancing basal shear stress and accelerating grounding line retreat. A common technique for detecting sub-glacial water involves analyzing the spatial variation in reflectivity from an airborne radar echo sounding (RES) survey. Basic RES analysis exploits the high dielectric contrast between water and most other substrate materials, where a reflectivity increase ≥ 15 dB is frequently correlated with the presence of sub-glacial water. There are surprisingly few additional tools to further characterize the size, shape, or extent of hydrological systems beneath large ice masses. We adapted an existing radar backscattering simulator to model RES reflections from sub-glacial water structures using the University of Texas Institute for Geophysics (UTIG) Multifrequency Airborne Radar Sounder with Full-phase Assessment (MARFA) instrument. Our series of hypothetical simulation cases modeled water structures from 5 to 50 m wide, surrounded by bed materials of varying roughness. We compared the relative reflectivity from rounded Röthlisberger channels and specular flat canals, showing both types of channels exhibit a positive correlation between size and reflectivity. Large (> 20 m), flat canals can increase reflectivity by more than 20 dB, while equivalent Röthlisberger channels show only modest reflectivity gains of 8–13 dB. Changes in substrate roughness may also alter observed reflectivity by 3–6 dB. All of these results indicate that a sophisticated approach to RES interpretation can be useful in constraining the size and shape of sub-glacial water features. However, a highly nuanced treatment of the geometric context is necessary. Finally, we compared simulated outputs to actual reflectivity from a single RES flight line collected over Thwaites Glacier in 2022. The flight line crosses a previously proposed Röthlisberger channel route, with an obvious bright bed reflection in the radargram. Through multiple simulations comparing various water system geometries, such as canals and sub-glacial lakes, we demonstrated the important role that topography and water geometry can play in observed RES reflectivity. From the scenarios that we tested, we concluded the bright reflector from our RES flight line cannot be a Röthlisberger channel but could be consistent with a series of flat canals or a sub-glacial lake. However, we note our simulations were not exhaustive of all possible sub-glacial water configurations. The approach outlined here has broad applicability for studying the basal environment of large glaciers. We expect to apply this technique when constraining the geometry and extent of many sub-glacial hydrologic structures in the future. Further research may also include comprehensive investigations of the impact of sub-glacial roughness, substrate heterogeneity, and computational efficiencies enabling more complex and complete simulations.
Mapping surface hoar from near-infrared texture in a laboratory
(Copernicus GmbH, 2024-05) Dillon, James; Donahue, Christopher; Schehrer, Evan; Birkeland, Karl; Hammonds, Kevin
Surface hoar crystals are snow grains that form when water vapor deposits on the snow surface. Once buried, surface hoar creates a weak layer in the snowpack that can later cause large avalanches to occur. The formation and persistence of surface hoar are highly spatiotemporally variable, making its detection difficult. Remote-sensing technology capable of detecting the presence and spatial distribution of surface hoar would be beneficial for avalanche forecasting, but this capability has yet to be developed. Here, we hypothesize that near-infrared (NIR) texture, defined as the spatial variability of reflectance magnitude, may produce an optical signature unique to surface hoar due to the distinct shape and orientation of the grains. We tested this hypothesis by performing reflectance experiments in a controlled cold laboratory environment to evaluate the potential and accuracy of surface hoar mapping from NIR texture using a near-infrared hyperspectral imager (NIR-HSI) and a lidar operating at 1064 nm. We analyzed 41 snow samples, three of which were surface hoar and 38 of which consisted of other grain morphologies. When using NIR-HSI under direct and diffuse illumination, we found that surface hoar displayed higher NIR texture relative to all other grain shapes across numerous spectral bands and a wide range of spatial resolutions (0.5–50 mm). Due to the large number of spectral- and spatial-resolution combinations, we conducted a detailed samplewise case study at 1324 nm spectral and 10 mm spatial resolution. The case study resulted in the median texture of surface hoar being 1.3 to 8.6 times greater than that of the 38 other samples under direct and diffuse illumination (p < 0.05 in all cases). Using lidar, surface hoar also exhibited significantly increased NIR texture in 30 out of 38 samples, but only at select (5–25 mm) spatial resolutions. Leveraging these results, we propose a simple binary classification algorithm to map the extent of surface hoar on a pixelwise basis using both the NIR-HSI and lidar instruments. The NIR-HSI under direct and diffuse illumination performed best, with a median accuracy of 96.91 % and 97.37 %, respectively. Conversely, the median classification accuracy achieved with lidar was only 66.99 %. Further, to assess the repeatability of our method and demonstrate its mapping capacity, we ran the algorithm on a new sample with mixed microstructures, with an accuracy of 99.61 % and 96.15 % achieved using NIR-HSI under direct and diffuse illumination, respectively. As NIR-HSI detectors become increasingly available, our findings demonstrate the potential of a new tool for avalanche forecasters to remotely assess the spatiotemporal variability of surface hoar, which would improve avalanche forecasts and potentially save lives.
Two-Lane Highways: Indispensable Rural Mobility
(MDPI AG, 2022-03) Al-Kaisy, Ahmed
Two-lane highways refer to roadways consisting of two lanes in the cross section, one for each direction of travel. Occasionally, passing lanes may be added to one or two sides of the roadway extending the cross section to three or four lanes at those locations. In this entry, two-lane highways strictly refer to roads in rural areas meeting the previous definition and do not include urban and suburban streets.
Capacity at All-Way Stop Control Intersections: Case Study
(SAGE Publications, 2023-08) Al-Kaisy, Ahmed; Doruk, Dorukhan
This paper presents an empirical investigation into the capacity of all-way stop-controlled (AWSC) intersections. Video data was collected over four days at an AWSC intersection site in Bozeman, Montana. The site is characterized by single-lane approaches and high level of vehicular and pedestrian traffic. Using strict protocols, video records were processed at the individual vehicle level and several information metrics were extracted for each vehicle in the data set on all approaches. Study results indicate that the total intersection capacity at the study site varied between 400 and 1,400 vehicles per hour. The study suggests that the wide range of capacity observations is largely associated with the pedestrian crossing activity at the study site. Statistical tests confirmed that both pedestrian crossing activity and the level of conflict have significant effects on intersection capacity at the 95% confidence level. For movement type, the right-turn movement was not found to have a significant effect on intersection capacity while left-turn movement was found to negatively affect the intersection capacity. The results presented in this paper offer valuable information on AWSC intersection capacity, given the limited amount of information in the literature and the dated nature of those empirical observations.
A Novel Network Screening Methodology for Rural Low-Volume Roads
(Scientific Research Publishing, Inc., 2023-01) Al-Kaisy, Ahmed; Raza, Sajid
Low-volume roads (LVRs) are an integral part of the rural transportation network providing access to remote rural areas and facilitating the movement of goods from farms to markets. These roads pose unique challenges for highway agencies including those related to safety management on the highway network. Specifically, traditional network screening methods using crash history can be effective in screening rural highways with higher traffic volumes and more frequent crashes. However, these traditional methods are often ineffective in screening LVR networks due to low traffic volumes and the sporadic nature of crash occurrence. Further, many of the LVRs are owned and operated by local agencies that may lack access to detailed crash, traffic and roadway data and the technical expertise within their staff. Therefore, there is a need for more efficient and practical network screening approaches to facilitate safety management programs on these roads. This study proposes one such approach which utilizes a heuristic scoring scheme in assessing the level of risk/safety for the purpose of network screening. The proposed scheme is developed based on the principles of US Highway Safety Manual (HSM) analysis procedures for rural highways and the fundamentals in safety science. The primary application of the proposed scheme is for ranking sites in network screening applications or for comparing multiple improvement alternatives at a specific site. The proposed approach does not require access to detailed databases, technical expertise, or exact information, making it an invaluable tool for small agencies and local governments (e.g. counties, townships, tribal governments, etc.).
A New Approach for Identifying Safety Improvement Sites on Rural Highways: A Validation Study
(MDPI AG, 2024-02) Dhakal, Bishal; Al-Kaisy, Ahmed
The research presented in this paper examines a new proposed approach for identifying safety improvement sites on rural highways. Unlike conventional approaches, the proposed approach does not require crash history, but rather utilizes classified variables for traffic volume, geometric features, and roadside characteristics that do not require access to exact data or extensive technical expertise. The research validates the performance of the proposed approach using field data from a large sample of rural two-lane highway segments in the state of Oregon including traffic, roadway, and crash data. A mathematical model for the prediction of the EB expected number of crashes using multivariate regression analysis is developed and used as the network screening criterion. The model’s independent variables include roadway geometry, roadside characteristics, and traffic exposure, while the dependent variable is the EB expected number of crashes. Using observed crash history as a reference, the performance of the proposed approach was compared to two of the well-established methods in practice, namely, the Empirical Bayes (EB) and the potential for safety improvement (PSI) methods. The study results suggest that by using crash density for highway segments, the performance of the proposed method was lower than that of the EB and PSI methods. This is despite the high R-square value of the predictive model used in the proposed method. However, when using crash frequencies for highway segments, the performance of the proposed method was found comparable to the well-established EB and PSI methods.
Pharmaceutical impacts on aerobic granular sludge morphology and potential implications for abiotic removal
(Elsevier, 2024-02) Bodle, Kylie B.; Kirkland, Catherine M.
The goal of this study was to investigate abiotic pharmaceutical removal and abiotic pharmaceutical effects on aerobic granular sludge morphology. For 80 days, a pharmaceutical mixture containing approximately 150 μg/L each of diclofenac, erythromycin, and gemfibrozil was fed to an aerobic granular sludge sequencing batch reactor and granule characteristics were compared with those from a control reactor. Aqueous and solid phase pharmaceutical concentrations were monitored and staining was used to assess changes in biofilm structures. Solid phase pharmaceutical concentrations were elevated over the first 12 days of dosing; however, they then dropped, indicative of desorption. The lipid content in pharmaceutical-exposed granules declined by approximately half over the dosing period, though the relative concentrations of other key biofilm components (proteins, alpha-, and beta-polysaccharides) did not change. Batch experiments were conducted to try to find an explanation for the desorption observed, but reduced solid phase pharmaceutical concentrations could not be linked with the presence of common wastewater constituents such as ammonia or phosphate. Sorption of all three compounds was modeled best by the Henry isotherm, indicating that, even at 150 μg/L, granules’ sorption site coverage was incomplete. Altogether, this study demonstrates that simplified batch systems may not accurately represent the complex abiotic processes occurring in flow-through, biotic systems.

Civil Engineering

Browse

Filters

Settings

Sort By

Results per page

Search Results